universal bus interface that talks to electronics from a computer serial terminal
1Hz-40MHz frequency measurement
5 volt tolerant pins-0-6volt measurement probe
1kHz-4MHz pulse-width modulator, frequency generator
10Hz-1MHz low-speed logic analyzer
(Grundpreis: 49,90 € / Stück)
inkl. MwSt. zzgl. Versand
What does “P” mean? “P” is for “panel mount” in this product. This Grove – Button is a sister version of original Grove - Button. They are identical except the Grove connecter is moved to the back so that you can easily use it as a neat and wire-free human interface device.
(Grundpreis: 3,90 € / Stück)
Grove - Universal 4 Pin connector is the white 4-pin buckled connector used on Stem, Twigs and the Grove cables, the pin spacing is 2mm. There are 10 connectors per bag, Users can use them to DIY.
(Grundpreis: 0,39 € / Stück)
This device is a programmer for AVR-based controllers, such as our Uno335. The programmer emulates an STK500 on a virtual serial port, making it compatible with standard AVR programming software. Two additional features help with building and debugging projects: a TTL-level serial port for general-purpose communication and a SLO-scope for monitoring signals and voltage levels. A USB cable and ISP cable are included.
(Grundpreis: 19,90 € / Stück)
This solar panel is made of single-crystal material that performs high solar energy transformation efficiency at 17%. It has a fine resin surface and sturdy back suitable for outdoor environments. A 2mm JST connecter is attached to the penal, which makes it perfect to team up with most of our can-use-solar-power-supply boards, like Seeeduino microcontroller series, Lipo Rider charging boards series and XBee carrier WSN products series.
The typical open circuit voltage is around 5V, depending on light intensity. In those bright summer days with clear sky and big sun, the peak OC voltage can rush up to 10V. To prevent any damage to boards that accept a narrow range of input voltage, like Lipo Rider, it’s recommended to check whether the OC voltage is safe before any connection.
(Grundpreis: 2,38 € / Stück)
(Grundpreis: 3,70 € / Stück)
This is a 3V battery holder with On/Off Switch and a lead pre-attached. You can use 2 AA battery of 3.0V using alkaline batteries or 2.4V using NiCD/NiMH rechargeable battery.
Battery not included.
(Grundpreis: 1,96 € / Stück)
This G1/2 micro hydro generator provides you clean and renewable electricity. With the help of the regulator circuit inside, the output of this generator is stable at 3.6V. And the capacity of battery is improved from 300mAh to 700mAh compared to the old version.
Time to replace the Li-po batteries in your waterside projects with the green and more accessible hydro power.
(Grundpreis: 28,10 € / Stück)
This is a battery holder with 150mm long wire. You can use AA-sized Alkaline or Rechargeable batteries with it. Batteries are not included.
(Grundpreis: 1,66 € / Stück)
This is lightweight, small size, high efficiency, low consumption and low noise water pump.
It has been used widely, in household include cooking, cleaning, bathing, space heating and water flowers, etc.
Note: Please do not test long time with no-load, inside is with plastic leaves, can't suction impurity.
(Grundpreis: 6,29 € / Stück)
The ATmega 328P is a 8bit microcontroller from Atmel based on the AVR instruction set. It is particulary popular in the maker community as it is used as main controller in the Arduino Uno board and its various clones.
(Grundpreis: 2,90 € / Stück)
(Grundpreis: 4,60 € / Stück)
(Grundpreis: 5,30 € / Stück)
USe this cable to connect two servo to Grove system with only 1 cable. Compatible with RB-421, MG-995, SG-90, SG-5010.
More information about how to choose a cable, please refer to this manual.
(Grundpreis: 4,30 € / Stück)
(Grundpreis: 4,06 € / Stück)
This module is an incremental rotary encoder. It encodes the rotation signal from the axis and output the signal by electronic pulse. The Grove – Encoder is one of the Grove series and has a standard Grove interface.
When you need to add a rotary knob to your project, for example a volume knob for a speaker, a selection panel or a digital input, this will be your first choice.
(Grundpreis: 4,54 € / Stück)
(Grundpreis: 18,40 € / Stück)
Grove - I2C FM Receiver is a wideband FM receiver module,this module is base on RDA5807M,The RDA5807M series is the newest generation single-chip broadcast FM stereo radio tuner with fully integrated synthesizer, The RDA5807M series has a powerful low-IF digital audio processor.Grove - I2C FM Receiver have a headset jack,it can driver earphone or audio.
(Grundpreis: 11,90 € / Stück)
This is a Grove interface compatible Magnetic switch module. It is based on encapsulated dry reed switch CT10. CT10 is single-pole, single throw (SPST) type, having normally open ruthenium contacts. The sensor is a double-ended type and may be actuated with an electromagnet, a permanent magnet or a combination of both. The magnetic switch is a wonder tool for designers who would like to turn a circuit on and off based on proximity.
(Grundpreis: 2,86 € / Stück)
Hey hey, calm down, have some fresh air here. The Grove – Mini Fan v1.1 can be set up in seconds and bring you some nice and cool air in the hot days. It has four parts, a mini fan, a DC Motor, a DC motor driver and a Grove cable. The cartoon-style fan design makes it good choice for decorating your little LEGO house as well
(Grundpreis: 9,00 € / Stück)
This protoshield allows you to add your own circuitry or components to your Grove system prototypes. This allows you access to all four lines from the connector cable ? S0, S1, VCC and GND. There is also an extra normally-open button to take advantage of. The hole spacing makes using normal DIP-format ICs and other components very simple. You may wish to purchase more for future use in advance.
(Grundpreis: 2,02 € / Stück)
Grove - Recorder is based on ISD9160FI and can record up to 83 sec. The module is very easy to control by push button on board or the microcontroller.
(Grundpreis: 16,90 € / Stück)
This slide potentiometer is a linear variable resistor with a total resistance of 10k. When you move the lever from one side to the other, its output voltage will range between 0 V to the VCC you apply. Three of four Grove pins are connected to VCC, GND and the ADC IN on the slide, while the remaining pin is connected to a green indicator LED. You can use the indicator LED to visually display the change on the potentiometer.
(Grundpreis: 5,39 € / Stück)
SPDT Relay(30A) is a high quality Single Pole Double Throw Relay(SPDT).The Relay consist of a coil, 1 common terminal, 1 normally closed(NC) terminal and one normally open(NO) terminal. When the coil of the relay is at rest (not energized), the common terminal and the normally closed terminal have continuity. When the coil is energized, the common terminal and the normally open terminal have continuity. This relay's coil is rated up to 5V and the contact is rated up to 30A (@250VAC, 30VDC). Use it to control AC appliances or high current DC devices.
What does “P” mean? “P” is for “panel mount” in this product. This Grove – Switch is a mini SPDT slide, great for “ON/OFF” situations. It’s such a reliable switch of great build quality that we adopt it on many of our boards. You should stock some for your Grove prototyping system.
This is a simple touch sensor module. You can use it to replace a traditional push button. Using the TTP223-B touch detector IC It measures the capacitance of a metallic pad. It can detect the change in capacitance when a finger is near it. This is the same technology used in the iPhone touch screen. So you can place the metallic pad under a non-metallic surface such as a plastic or glass sheet and it will still work as a button. This may be useful for projects that need to be waterproof. You can also make a secret button by placing it inconspicuously behind a smooth surface. For instance you could place them under a nonmetallic card table and by casually pressing the right location on a tabletop surface you could mysteriously control your DIY project.
Compared with the Electronic Brick system, the Grove System uses only 1 type of cable, (the Electronic Brick system uses 4). These cables are compatible with all modules included in the Grove system.
5 cables are included in this pack.
(Grundpreis: 2,50 € / Stück)
Grove - Water Atomization is a perfect module for you to develop an atomizer or an atomizer module in your applications easily. With just a few simple steps, you can prototype an atomizer. It has Grove interface which makes it easy to be integrated into plenty of applications. A humidifier is a basic device it can be built with, you can develop more advanced and interesting projects with digital scent technology and any other situations in which atomization required.
(Grundpreis: 12,36 € / Stück)
This is a simple yet enjoyable twig to use. The piezo can be connected to digital outputs, and will emit a tone when the output is high. Alternatively it can be connected to an analog pulse-width modulation output to generate various tones and effects.
(Grundpreis: 2,40 € / Stück)
The potentiometer twig produces analog output between 0 and Vcc (5V DC with Seeeduino) on its D1 connector. The D2 connector is not used. The angular range is 300 degrees with a linear change in value. The resistance value is 10k ohms, perfect for Arduino use. This may also be known as a rotary angle sensor.
The tilt-switch twig is the equivalent of a button, and is used as a digital input. When the switch is level it is open, and when tilted, the switch closes. It is wired to the SIG line, NC is not used on this twig. There's a surface-mount resistor .
Power your favorite electronic kit with green energy! The LiPo Rider Pro is a enhancement of LiPo Rider. It can supply higher load output than LiPo Rider. The LiPo Rider Pro board allows you ride the solar wave to run your favorite 5V device. The LiPo Rider Pro board is the ideal green power solution for your outdoor sensor design. Attach the LiPo Rider Pro board to your sensor board and it can run on solar power forever! It can also be used to charge mobile phone.
This in-system programmer can be used to program AVR microcontrollers and AVR-based controller boards, such as our Orangutan robot controllers and the 3pi robot. The programmer emulates an STK500 on a virtual serial port, making it compatible with standard AVR programming software, and it supports devices running at either 3.3 V or 5 V. The programmer also features a TTL-level serial port, enabling general-purpose serial communication for debugging or programming microcontrollers with a serial bootloader. An ISP cable and a 1×6 double-sided male header are included with the fully-assembled programmer.
(Grundpreis: 12,90 € / Stück)
Type-B USB cable, cable length 1.5m . Compatible with Arduino Uno.
(Grundpreis: 1,80 € / Stück)
Der UnoSWU ist eine Smarte Steckdose, die durch Anlegen einer kleinen ungefährlichen Spannung, die Netzspannung ein- und ausschalten kann. Zusätzlich und das ist die Neuerung, bietet die UnoSWU auch eine Spannungsversorgung von 5V für kleine Computer (z. B. Arduino© oder RaspberryPi©), die dann die Steuerung der Steckdose übernehmen können. Somit entfällt das oftmals lästige Problem, das man eine Schaltung entwickelt hat, die eine Steckdose kontrolliert, diese aber mühsam durch Batterien oder gar mittels Netzteil aus einer zweiten Steckdose mit Strom versorgt werden muss.
(Grundpreis: 79,00 € / Stück)
USB To Uart 5V/3V3 is a USB to serial adapter,Which is base on CH340,CH340 is a USB bus convert chip and it can realize USB convert to serial interface, USB convert to IrDA infrared or USB convert to printer interface. this module is compatible with 5V and 3v3.and it can used for upload code or communicating with MCUs.
(Grundpreis: 8,09 € / Stück)