This solar panel is made of single-crystal material that performs high solar energy transformation efficiency at 17%. It has a fine resin surface and sturdy back suitable for outdoor environments. A 2mm JST connecter is attached to the penal, which makes it perfect to team up with most of our can-use-solar-power-supply boards, like Seeeduino microcontroller series, Lipo Rider charging boards series and XBee carrier WSN products series.
The typical open circuit voltage is around 5V, depending on light intensity. In those bright summer days with clear sky and big sun, the peak OC voltage can rush up to 10V. To prevent any damage to boards that accept a narrow range of input voltage, like Lipo Rider, it’s recommended to check whether the OC voltage is safe before any connection.
(Grundpreis: 2,38 € / Stück)
inkl. MwSt. zzgl. Versand
This is a segment LED bar without control chip. It has 10 segment LEDs, including of 8 green, 1 yellow and 1 red. It is compatible with bread board and can work with Arduino by adding some current limiting resistors. Since it has 10 pin, it may be complex to control.
(Grundpreis: 1,66 € / Stück)
This is a segment LED bar without control chip. It has 10 segment LEDs, including of 8 green, 1 yellow and 1 red. It is compatible with bread board and can work with Arduino by adding some current limiting resistors. Since it has 10 pin, it may be complex to control. If you would like a modular segment LED bar, see the Grove - LED Bar.
(Grundpreis: 3,70 € / Stück)
This is a 3V battery holder with On/Off Switch and a lead pre-attached. You can use 2 AA battery of 3.0V using alkaline batteries or 2.4V using NiCD/NiMH rechargeable battery.
Battery not included.
(Grundpreis: 1,96 € / Stück)
V-14001 is a high integration small size Bluetooth 4.0 module.
(Grundpreis: 14,82 € / Stück)
This G1/2 micro hydro generator provides you clean and renewable electricity. With the help of the regulator circuit inside, the output of this generator is stable at 3.6V. And the capacity of battery is improved from 300mAh to 700mAh compared to the old version.
Time to replace the Li-po batteries in your waterside projects with the green and more accessible hydro power.
(Grundpreis: 28,10 € / Stück)
This is a battery holder with 150mm long wire. You can use AA-sized Alkaline or Rechargeable batteries with it. Batteries are not included.
This is lightweight, small size, high efficiency, low consumption and low noise water pump.
It has been used widely, in household include cooking, cleaning, bathing, space heating and water flowers, etc.
Note: Please do not test long time with no-load, inside is with plastic leaves, can't suction impurity.
(Grundpreis: 6,29 € / Stück)
A super case to protect your Arduino Uno board. Constructed from 2.8mm crystal clear acrylic, this snap together case is supplied with all hardware to assemble and mount your Ardunio board.
(Grundpreis: 5,87 € / Stück)
(Grundpreis: 4,60 € / Stück)
The BlueDuino Rev2 is an Arduino compatible microcontroller development board based on the ATmega32U4 IC with Bluetooth 4.0. a.k.a. Bluetooth Low Energy (BLE), built in. Just plug in the board and your ready to start programming! It's the easiest way to get Bluetooth 4.0 in your project!
(Grundpreis: 14,28 € / Stück)
Der neue Umweltsensor BME280 von Bosch Sensortec vereinigt Druck, Temperatur und Luftfeuchte Messung auf einem winzigen Chip. Mit Hilfe dieses Chips ist es ganz einfach Wetterstationen etc. aufzubauen. Als Schnittstelle unterstützt der Chip sowohl I2C als auch SPI. Zudem haben wir dem Breakout board einen Stecker für das Grove System von Seeedstudio verpasst so das er dort sehr einfach eingebunden werden kann.
The BME280 is a pretty new environmental sensor from Bosch measuring Pressure, Humidity and Temperature on one chip with pretty high precision. The sensor communicates through SPI and I2C. Actually we are still working on our own software but until this is ready you can use some of the libraries out there. We put also an Grove connector on the breakout to embed it into the SeeedStudio Grove Ecosystem. PLEASE NOTE the board is not 5V tolerant!!
(Grundpreis: 8,90 € / Stück)
We sourced these beautiful RGB LED matrix panels from Shenzhen. These panels make cool display devices.
The Arduino Uno is not able to drive this RGB LED matrix but you can use Arduino Mega, RaspberryPi,
BBB, BBG. On the back of this panel are two IDC connectors (1x input and 1x output).
Power this panel with 5V 4A. Control the RGB LED matrix with 13 digital pins allowing you to drive the LED matrix at a 1:16 scan rate.
(Grundpreis: 61,75 € / Stück)
Das EE893 Sensor Module wurden speziell für OEM-Anwendungen und anspruchsvolle Umgebungsbedingungen konzipiert. Die Mehrpunkt CO2- und Temperaturjustage sorgt für eine ausgezeichnete Messgenauigkeit über den gesamten Temperatureinsatzbereich.
(Grundpreis: 79,50 € / Stück)
(Grundpreis: 82,00 € / Stück)
The ADXL335 is a small, thin, low power, complete 3-axis accelerometer with signal conditioned voltage outputs. The product measures acceleration with a minimum full-scale range of ±3 g.
The module was designed as breakout board because ADXL335's signal is analog( more ports requested ),but the board outline is grove module that you can fix it convenient like others grove. The sensor combine 3.3 and 5V power supply,can be used in standard arduino device and seeeduino stalker.
(Grundpreis: 8,75 € / Stück)
Based on the excellent ADXL-345, this digital 3-axis accelerometer has excellent EMI protection. Its variable output makes it suitable for a wide range of applications:
• HDD shock protection
• Vibration sensor
• Game controller input
• Smart vehicles
• Anywhere you need to obtain motion-sensing & orientation information.
(Grundpreis: 9,90 € / Stück)
The 80cm Infrared Proximity Sensor is a General Purpose Type Distance Measuring Sensors, this sensor takes a continuous distance reading and returns a corresponding analog voltage with a range of 10cm (4") to 80cm (30"). Can be used in TVs,personal computers ,cars and so on.
(Grundpreis: 16,40 € / Stück)
Alcohol sensor is semiconductor sensor for alcohol detection. It has good sensitivity and fast response to alcohol, suitable for portable alcohol detector.
(Grundpreis: 7,07 € / Stück)
This Grove - BLE utilizes an HM-11 module to provide your Arduino/Seeeduino with serial BLE function, and it can be used with Arduino/Seeeduino very conveniently if using with Base Shield together. With support for a BLE ComAssistant APK, this Grove - BLE can talk to your mobile phone more easily without pairing, and of course, it can be set via AT commands directly. You can use it in many conditions, like robot controls or remote control equipment ,etc. We prepared an easy and convenient command set for this product so that
(Grundpreis: 17,16 € / Stück)
USe this cable to connect two servo to Grove system with only 1 cable. Compatible with RB-421, MG-995, SG-90, SG-5010.
More information about how to choose a cable, please refer to this manual.
(Grundpreis: 4,30 € / Stück)
Find setting up an amplifier IC on the breadboard a troublesome and totally no-need-to-repeat job? This Grove module can save you clutter to settle up such an IC by integrating the whole operating circuit. It's designed for precise differential-input amplification. Input the differential signals of your sensor to this module through the male pins, then your Arduino will get a precisely amplified output from the Grove interface. The gain scale factor is selectable. You can get a 35 times or 1085 times amplification via a switch on the board
(Grundpreis: 12,96 € / Stück)
This module is based on the I2C light-to-digital converter TSL2561 to transform light intensity to a digital signal. Different from traditional analog light sensor, as Grove - Light Sensor, this digital module features a selectable light spectrum range due to its dual light sensitive diodes: infrared and full spectrum.
You can switch between three detection modes to take your readings. They are infrared mode, full spectrum and human visible mode. When running under the human visible mode, this sensor will give you readings just close to your eye feelings.
(Grundpreis: 4,06 € / Stück)
(Grundpreis: 16,90 € / Stück)
(Grundpreis: 75,90 € / Stück)
This module is an incremental rotary encoder. It encodes the rotation signal from the axis and output the signal by electronic pulse. The Grove – Encoder is one of the Grove series and has a standard Grove interface.
When you need to add a rotary knob to your project, for example a volume knob for a speaker, a selection panel or a digital input, this will be your first choice.
(Grundpreis: 4,54 € / Stück)
The Grove - Gas Sensor(MQ2) module is useful for gas leakage detecting(in home and industry). It can detect LPG, i-butane, methane, alcohol, Hydrogen, somke and so on. Based on its fast response time. measurements can be taken as soon as possible. Also the sensitivity can be adjusted by the potentiometer.
(Grundpreis: 6,23 € / Stück)
The Grove - Gas Sensor module is useful for gas leakage detecting(in home and industry). It can detect LPG, i-butane, methane, alcohol, Hydrogen, somke and so on. Measurements can be taken as soon as possible based on its fast response time. Also the sensitivity can be adjusted by the potentiometer.
The Grove - Gas Sensor(MQ5) module is useful for gas leakage detecting(in home and industry). It can detect LPG, natural gas, town gas and so on. Based on its fast response time. measurements can be taken as soon as possible. Also the sensitivity can be adjusted by the potentiometer.
Grove-Gas Sensor (O₂) is a kind of sensor to test the oxygen concentration in air, which is based on the principle of the electrochemical cell to the original work. You can know clearly the current oxygen concentration when you output voltage values proportional to the concentration of oxygen and refer to the oxygen concentration linear characteristic graph. It’s very suitable for detecting oxygen concentration in the environment protection.
(Grundpreis: 57,19 € / Stück)
The Hall Sensor measures the Hall Effect, which is a production of a voltage difference across an electrical conductor, transverse to an electric current in the conductor as well as a magnetic field perpendicular to the current. The output of the continuous-time switch Hall sensor on this Twig switches low and turns on when a magnetic field (south polarity) perpendicular to the Hall sensor exceeds the BOP threshold, and it switches high and turn on when the magnetic field disappears.
(Grundpreis: 7,40 € / Stück)
Grove - I2C FM Receiver is a wideband FM receiver module,this module is base on RDA5807M,The RDA5807M series is the newest generation single-chip broadcast FM stereo radio tuner with fully integrated synthesizer, The RDA5807M series has a powerful low-IF digital audio processor.Grove - I2C FM Receiver have a headset jack,it can driver earphone or audio.
(Grundpreis: 11,90 € / Stück)
Grove - IMU 10DOF is based on MPU-9250 and BMP180, it combines a 3-axis gyroscope, 3-axis accelerometer, 3-axis magnetometer and barometer in standard Grove module. Total 10 degrees of freedom make it suitable for mobilephone, aircraft, smart watch etc.
(Grundpreis: 15,48 € / Stück)
The Infrared Emitter is used to transmit infrared signals through an infrared LED, while there is an Infrared receiver to get the signals on the other side . An infrared LED is like any other LED, with its color centered around 940nm. We can use the emitter not only to transmit data or commands, but also to emulate remotes to control your home appliance using an Arduino. The Infrared Emitter can transmit signals reliable up to 10 meters. Beyond 10 meters, the receiver may not get the signals.
(Grundpreis: 5,70 € / Stück)
The Infrared Receiver is used to receive infrared signals and also used for remote control detection. There is a IR detector on the Infrared Receiver which is used to get the infrared light emitted by the Infrared Emitter. The IR detector have a demodulator inside that looks for modulated IR at 38 KHz. The Infrared Receiver can receive signals well within 10 meters. If more than 10 meters , the receiver may not get the signals. We often use the two Twigs-the Infrared Receiver and the Infrared Emitter to work together.
(Grundpreis: 5,90 € / Stück)
This Grove-Infrared temperature sensor is a non-contact temperature measure model.The sensor is composed of 116 elements of thermocouple in series on a floating micro-membrane having an active diameter of 545μm and with blacken surface to absorb the incident thermal infrared radiation, which induces a voltage response at output terminals.
This IR Distance Interrupter features a high-sensitivity RFR-359F photoreflector to perform distance detection function. The photoreflector consists of a GaAs infared light emitting diode and a silicon planar phototransistor. When the infrared light emitted by the emitter gets reflected on a surface that blocked it, the phototransistor can pick up the signal for distance calculation. This module is panel mounted so that you can easily implement it on the surface of robots or other projects without wiring clutter. Also a potentiometer for adjustment and an indicator LED are arranged on the back for easy and clear use.
(Grundpreis: 5,39 € / Stück)
The Light sensor module uses the GL5528 photoresistor to detect the light intensity of the environment. The resistance of the sensor decreases when the light intensity of the environment increases. The chip LM358 is used as a voltage follower to enable you get a accurate data.
(Grundpreis: 2,86 € / Stück)